Affinity Designer incorrectly displays the stroke thickness in numbers

[AndrewSanders]

In version 2.2.0, Affinity Designer (PC) found that the stroke thickness in numbers is not displayed. When I move the slider, I don't see any changes in the numbers. The changes are visible only after I release the slider. But, in the panel on the right, everything is displayed correctly. Or is it not a problem and should it be?

Edited September 23, 2023 by AndrewSanders

[firstdefence]

Possibly the decimal places that are set in the settings. Try increasing the decimal places for the units you are using.

[AndrewSanders]

56 minutes ago, firstdefence said:

Possibly the decimal places that are set in the settings. Try increasing the decimal places for the units you are using.

Please tell me where these settings can be found? I can't do it

[AndrewSanders]

1 hour ago, firstdefence said:

Possibly the decimal places that are set in the settings. Try increasing the decimal places for the units you are using.

The stroke thickness is not displayed in pt in the upper menu

[walt.farrell]

3 hours ago, AndrewSanders said:

Please tell me where these settings can be found? I can't do it

Settings, User Interface.

[AndrewSanders]

5 minutes ago, walt.farrell said:

Settings, User Interface.

 

5 minutes ago, walt.farrell said:

Settings, User Interface.

Yes, thank you. But the stroke thickness is not displayed in pt in the upper menu

[walt.farrell]

14 minutes ago, AndrewSanders said:

But the stroke thickness is not displayed in pt in the upper menu

It seems to be shown in pt in your screenshots above. What am I missing?

In any case, another relevant setting might be the one to "show lines in points" (not sure of the name, might be in the same part of the Settings).

[AndrewSanders]

16 minutes ago, walt.farrell said:

Кажется, на ваших скриншотах выше это показано в pt. Чего я не понимаю?

В любом случае, другой соответствующей настройкой может быть параметр "показывать линии в точках" (не уверен в названии, возможно, находится в той же части настроек).

I mean, when I move the slider in the stroke settings, the width in pt does not change until I release the slider. I.e. I do not immediately see how much I increase the stroke, only after I release the slider

[iconoclast]

I can confirm that behavior. The values of the stroke slider in the toolbar don't change until I release the slider, while they change simultaneously in the stroke panel. "Show Lines in Points" is activated in my settings. I think it's a bug.

I'm on Windows 10.

Edit: It's the same, by the way, in Photo and Publisher 2.2. In Designer 1.10.6 it works correctly.

[AndrewSanders]

1 hour ago, iconoclast said:

I can confirm that behavior. The values of the stroke slider in the toolbar don't change until I release the slider, while they change simultaneously in the stroke panel. "Show Lines in Points" is activated in my settings. " is activated in my settings. I think it's a bug.

I'm on Windows 10.

Edit: It's the same, by the way, in Photo and Publisher 2.2. In Designer 1.10.6 it works correctly.

I tried it. Disabled this option, but the problem is not fixed.

[carl123]

 

 

[AndrewSanders]

41 minutes ago, carl123 said:

 

 

Do you mean that you need to turn on, turn off OpenCL computer acceleration?

[AndrewSanders]

47 minutes ago, carl123 said:

 

 

I tried, the situation has not changed. The problem is not solved

[R C-R]

16 hours ago, AndrewSanders said:

I mean, when I move the slider in the stroke settings, the width in pt does not change until I release the slider. I.e. I do not immediately see how much I increase the stroke, only after I release the slider

For what little it is worth, this problem does not occur on the Mac versions so it is probably a (minor?) bug in the Windows ones.

[AndrewSanders]

52 minutes ago, R C-R said:

For what little it is worth, this problem does not occur on the Mac versions so it is probably a (minor?) bug in the Windows ones.

I hope that this error will be corrected. She is not critical, but spoils the impression

[Lee D]

@AndrewSanders I've updated the existing report that's with our developers to include yours. 

[AndrewSanders]

2 hours ago, Lee D said:

@AndrewSanders I've updated the existing report thats with our developers to include yours. 

Thanks!