Perspective logo

[Luc DW]

Hello, I want to make a simulation of a logo on a truck.
When I placed the logo on the side of the truck, I click "warp", I loose parts of the logo.
What am I doing wrong.

Step 1: new file

Step 2: placed picture (jpeg of truck)

Step 3: placed logo (saved as affinity document or pdf)

Step 4: klicked layer in the layers panel and then on warp>perspective.

When I pull the nodes it goes wrong.

Thanks

[v_kyr]

Which ADe version do you use and Is your logo all plain vectors?

However, there were some known issues for ADe v2 warp & perspective functions ...

• "affinity designer" 2023 warp bug site:forum.affinity.serif.com

[Luc DW]

Hello I use version 2.1.1 on mac and have installed all the updates.

 

Thanks 

[Luc DW]

Logo is a vector, picture is jpeg

 

[v_kyr]

Could be also a some sort of redrawing problem, try to zoom in/out and back, in order to see if that changes anything on the visual representation.

See also related ...

 

[Luc DW]

I tried it, and looked at the video, without succes. Sorry.
I will make the perspective in Affinity photo.

 

If I put the word perspective on the picture,  I have no problems for putting it in perspective.

Thank you very much for the help.

Kind regards

Luc

[v_kyr]

51 minutes ago, Luc DW said:

Step 2: placed picture (jpeg of truck)

Step 3: placed logo (saved as affinity document or pdf)

Here with place you mean via "File -> Place..." or dragging them into your doc? - If yes, then those are treated as embedded documents in an own container then and you would have to use edit document for your in the layers panel selected logo part. - So what you can also do is opening the logo DOC/PDF into a seperated tab (via "File -> Open..."), select it's grouped layers and copy/paste that into your initial doc with the background pixel image. Then retry performing the perspective warp on the selected logo parts.

[SolidSnake2003]

Did you try using the perspective warp live effect in the live effects to get the perspective you want?

[Luc DW]

Thanks, thats the solution. 

I open the image of the truck.

Open the vector of the logo.

Behind the logo I put a transparant square of the right size (available on the truck in this case)

Copy

Past on the image 

And than I can use warp without any problem.

 

Thanks again for the help!

Luc

[v_kyr]

3 minutes ago, SolidSnake2003 said:

Did you try using the perspective warp live effect in the live effects to get the perspective you want?

The OP uses ADe and vector warp/perspective here for his logo part placed and altered on a background pixel image.

[SolidSnake2003]

1 minute ago, v_kyr said:

The OP uses ADe and vector warp/perspective here for his logo part placed and altered on a background pixel image.

Thanks, sorry I made a bad suggestion.

[TrentL]

5 hours ago, Luc DW said:

Thanks, thats the solution. 

I open the image of the truck.

Open the vector of the logo.

Behind the logo I put a transparant square of the right size (available on the truck in this case)

Copy

Past on the image 

And than I can use warp without any problem.

 

Thanks again for the help!

Luc

For a bitmap, I believe you need to use Affinity Designer's Pixel Persona and then choose Layer -> New Live Filter Layer -> Perspective. 

The variety of perspective tools is a little confusing to say the least. 

[v_kyr]

9 minutes ago, TrentL said:

For a bitmap, ...

For a bitmap logo yes, but the OP's logo is instead vectors here ...

6 hours ago, Luc DW said:

Logo is a vector, picture is jpeg

... which he placed on a bitmap truck background image. And he wanted to warp (bring into perspective) that vector logo part on top of the truck background image. - Take a look at his above shown screenshots.