Jump to content
Sign in to follow this  
larsh

Moving inside?

Recommended Posts

Hi, what is the command: moving inside? If click on the pic is gone. I hoped to move it inside the frame, if the frame is smaller as the pic. Thanks, lars


AP 1.6.7 // AD 1.6.1 // Apu ß: Capture One+; MacBook Pro, OSX 10.13.1, early 2012 (ret), flsh 256 GB, RAM 16 GB; // Fuji X-Pro2, XF 18 - 55, XF 55 - 200 mm, nikkor 2.8/ 20 mm with shift 

Share this post


Link to post
Share on other sites

WE TRY AGAIN


AP 1.6.7 // AD 1.6.1 // Apu ß: Capture One+; MacBook Pro, OSX 10.13.1, early 2012 (ret), flsh 256 GB, RAM 16 GB; // Fuji X-Pro2, XF 18 - 55, XF 55 - 200 mm, nikkor 2.8/ 20 mm with shift 

Share this post


Link to post
Share on other sites

Hi larsh,
The command Arrange ▸ Move Inside / Outside moves the selected layer to inside (clipping it) or outside (unclipping it) the layer below. It's the same operation as dragging a layer over another layer in the Layers panel (not over its thumbnail but over the label area on the right). It can be used to move an image layer to inside a picture frame if that's what you meant.

Share this post


Link to post
Share on other sites

Hi, please think about this, I asked month ago: to move a pic inside the frame, if the frame is smaller as the pic. Thanks, lars 


AP 1.6.7 // AD 1.6.1 // Apu ß: Capture One+; MacBook Pro, OSX 10.13.1, early 2012 (ret), flsh 256 GB, RAM 16 GB; // Fuji X-Pro2, XF 18 - 55, XF 55 - 200 mm, nikkor 2.8/ 20 mm with shift 

Share this post


Link to post
Share on other sites

@MEB let me help, I think @larsh want to move a picture inside a picture frame, even if the picture is smaller than the frame. I think you have 2 options. 1 - Expand the picture frame in the layers panel and then select the picture itself and them move it as you normally do. The other one is, when you select the picture frame you have a bar that appear on the bottom with one little arrow in black thal let you move your picture and a zoom bar that let you choose the size of the picture.

Is this what you looking for?

Hope this helps.

Share this post


Link to post
Share on other sites
2 hours ago, dcarvalho84 said:

even if the picture is smaller than the frame

No, I would like to move an image inside of the frame if the image is bigger (!) then the frame. So I can first see and then say in APu what I want to show (and must not go back to APh to change the pic). There may be a part of the page I will test the design: so or so or others... So the frame can be changed: smaller, longer... And the image should be move into the new form of the frame with its best part. 

Ich möchte den Rahmen beim Design ändern können, ohne erst eine neue Grösse des Bildes zu machen. Den Rahmen verändern, kleiner, länger. Und dann möchte ich das Bild entsprechend der Komposition neu im Rahmen positionieren (um am Ende vielleicht zur ersten Form zurückzukehren). Gruss, lars


AP 1.6.7 // AD 1.6.1 // Apu ß: Capture One+; MacBook Pro, OSX 10.13.1, early 2012 (ret), flsh 256 GB, RAM 16 GB; // Fuji X-Pro2, XF 18 - 55, XF 55 - 200 mm, nikkor 2.8/ 20 mm with shift 

Share this post


Link to post
Share on other sites

Hi larsh,
Do you mean you want to see the whole image while you move it inside the frame? Currently the parts that lay outside the picture frame are faded while you move it (see clip below). Sorry the questions but I'm still unsure about what you are trying to achieve. With the Move Tool you can also change the frame size or the image size independently from each other depending on what layer you have selected in the Layers panel - also show in the animated (loop) gif below.

1277700948_2019-01-2915_47_44.gif.0d5507be262cd8d218f8180ea9ae58e7.gif

Share this post


Link to post
Share on other sites

WUNDERFULL!!!

If one – as I allways do – not make the frame first and then include the pic, but moves the image using the: include image button direct to the page, the pic becomes a frame. Two movings and the pic is where it shall be (1. up to left edge of marvins, 2. right down to bring it to the right marvin). But in the layer-table is no special second layer shown with the image. Is there a way to do my way and then open the second layer? 

THANKS, lars


AP 1.6.7 // AD 1.6.1 // Apu ß: Capture One+; MacBook Pro, OSX 10.13.1, early 2012 (ret), flsh 256 GB, RAM 16 GB; // Fuji X-Pro2, XF 18 - 55, XF 55 - 200 mm, nikkor 2.8/ 20 mm with shift 

Share this post


Link to post
Share on other sites

If you have an image that is not inside of a frame and want to place it in a frame, create the frame and drag the image's layer in the Layers studio panel over the label (not the thumbnail) of the frame's layer.  A line should appear below the frame's layer which should be somewhat indented from the left edge of the list but go nearly to the end on the right.

Is that what you are looking for?

Share this post


Link to post
Share on other sites

Ja, thanks, that works. Better was, to click in the pic double and to get an arrow then and a main frame in the layer field, as it is on the frame layer. But for me it is ok now. Regards, lars


AP 1.6.7 // AD 1.6.1 // Apu ß: Capture One+; MacBook Pro, OSX 10.13.1, early 2012 (ret), flsh 256 GB, RAM 16 GB; // Fuji X-Pro2, XF 18 - 55, XF 55 - 200 mm, nikkor 2.8/ 20 mm with shift 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×